some landscape designs call for a deck to join with a cinder block wall at a property line, a building or a planter. the deck-to-block connection is done with a ledger board attached to the block
learn how to attach the ledger to the house. on this project, the 2×10 joists of the main deck frame sit just about even with the top of the foundation, and a landing framed with 2x8s sits atop the main frame, serving as a transition point between the lowered deck and the patio door. in this episode we show you how to lay out the ledger fasteners,
connecting wood to concrete can seem intimidating but, with the right tools, even an amateur craftsman can do it. you can fasten wood to concrete using 3 different methods, depending on your preference. hammer-set concrete fasteners, concrete screws, and mortar nails are all effective ways to connect wood to concrete.
using that tiny l-bracket to attach a deck post to concrete is like using a piece of thread to hold a cruise ship to a pier. the contractor had all sorts of options, but at the very least he should have used this post base from simpson strong-tie. i've used these for years with great success. see the image below.
snap the cutting line on the deck. then measure from the edge of your saw blade to the edge of your saws base. mark that distance from the line and screw down a straight board. run the saws base against the straightedge to cut the deck boards perfectly straight.
yupjust drill a hole, add a piece of copper wire and drive the screw home when i have to attach a piece of wood to concrete, concrete block, brick or any similar hard surface it's not always practical to buy a box of specialty concrete fasteners, especially when i usually have a full assortment of torx-drive 'deck screws' on hand when framing.
fastening a ledger to concrete: the ledger is not only the structural connection between the deck and the house; its also what establishes the overall height and levelness of the entire deck frame. on this project, the 2×10 joists of the main deck frame sit just about even with the top of the
how to attach composite decking to concrete ehow composite decking is a low-maintenance alternative to traditional wood decking. composite decking is composed of a mixture of wood and plastic and offers the look of
how to make epoxy cutting boards - duration: 16:23. how to attached wood to concrete that is well cured. over a concrete deck - duration: 3:17. theoldkid888 106,482 views.
once everything is laid out and pre-drilled, attach the two-by-fours to the concrete with three-and-a-quarter-inch-long concrete screws. while you attach your sleepers, use a level to ensure that the boards are level in the direction that parallels the house.
re: attaching seven trust to an existing concrete patio mlb construction you got it right the first time. attach furring strips to the concrete with tapcons and use the correct screws to attach the decking to the furring strips.
set the first board along a chalk line to start straight. then sight down the boards occasionally to make sure theyre staying straight. if theyre not, vary the size of the gap between boards gradually over a few rows as needed to straighten them. the slight changes in deck board spacing wont be noticeable in the finished deck.
attach trim boards to concrete with masonry anchors; tap in anchors with hammer , then finish with a nail set 7. use a attach the wood-composite decking to the top of the concrete stoop using the same masonry anchors.
but you cant just put wood porch/deck boards directly onto concrete. first, you have to attach risers/sleepers to the concrete and then the porch boards can be screwed to the risers. so the plan yesterday was to get all of the risers/sleepers attached to the porch.
in order for a wooden stairway to be safe, the stringers support boards should be securely fastened to both the upper and lower floors. when the lower floor is made of concrete, you will need a special fastener to attach the wood to it unless one has already been embedded for this purpose.
when we reached the end of the deck, we removed the center divider board and cut it to final length. then we removed and mitered the border boards and trimmed the sleepers to final length. to cover the ends of the sleepers, we used a deck fascia board made from 1/2-in.-thick pvc. we cut the fascia into strips and screwed them to the sleepers.
how to install deck piers. deck piers support the beams that create the joist spans for a deck. this is the foundation of the deck and if not properly installed will result in failure of part or the entire deck. unlike a concrete footing
this is a time-consuming process and its difficult to create even, straight boards this way, which in turn makes it harder to build a level deck. preparing the surface by leveling the slab once youve determined your concrete slab has the required clearance, the real challenge is ensuring the frame is level so that the resulting deck is level.
attach the finished skirts to the concrete using tapcon screws and you're done. you can then quickly remove the stair boards to apply silicone where the skirts touch the concrete, and put the boards back on. notes cupping - if you look down the short edge of a board, you'll see the rounded grain that indicates this was once part of a circle. the curves will either point up or down, and this is important to keep in mind.
Shanghai Seven Trust Industry Co., Ltd, founded in the year 2008, is a hi-tech enterprise which specializes in the R&D, sales, and service of WPC materials, Provide excellent products, professional technology and sincere service.